Book

 

Do you find yourself hunting for additional info on How to Install a Bathtub: Install an Acrylic Tub and Tub Surround?

Mounting a bathtub isn't specifically rocket science, but it does need strong plumbing, carpentry, and in some cases, tiling skills. Changing an old bath tub with a brand-new one is additionally a reasonably hard project. If the old bathtub is conveniently accessible, the job can move quickly; if you need to open a wall to remove the old tub and place the brand-new tub, the job is much harder. In either case, the task is within a residence handyman's skills, although you will certainly need a helper to move out the old tub as well as set in the new one. Ensure you have actually qualified yourself for the work as well as fit trying it. Rather than working with a service provider to take control of a halfway-completed task, it is better to take into consideration utilizing one before you start. Opportunities are you might need an expert plumber to make tube connections.
This article will assist you install a new bath tub in your restroom if you have currently bought a new bathtub and don't require to transform the arrangement of your previous water system pipes.
Your tools and material checklist ought to comprise the following:

 

• New Bath tub


• Hammer


• Pipeline Wrenches


• Prybar


• Shatterproof glass


• Level


• Pliers


• Adjustable Wrench


• Putty Blade


• Screwdriver


• Cold Blade


• Measuring tape


• Pipeline Caps


 

Getting ready for the Installation

First of all, the sustaining frame provided with the bathroom needs to be fitted (if required) according to the maker's instructions. Next off, fit the faucets or mixer to the bathtub. When suitable the tap block, it is necessary to ensure that if the tap features a plastic washing machine, it is fitted in between the bath as well as the faucets. On a plastic bathroom, it is likewise reasonable to fit a sustaining plate under the taps device to avoid pressure on the bath tub.
Fit the flexible faucet adapters to the bottom of both faucets utilizing 2 nuts and also olives (sometimes provided with the bathtub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink electrical outlet opening, and then pass the outlet through the hole in the bathroom. Utilize the nut provided by the maker to fit the plug-hole. Analyze the plug-hole electrical outlet for an inlet on the side for the overflow pipe.
Next off, fit the end of the versatile overflow pipeline to the overflow outlet. Afterwards, screw the pipeline to the overflow face which ought to be fitted inside the bathroom. Make sure you make use of all of the provided washing machines.
Attach the trap to the bottom of the waste outlet on the tub by winding the thread of the waste electrical outlet with silicone mastic or PTFE tape, as well as screw on the catch to the electrical outlet. Attach all-time low of the overflow tube in a comparable manner.The bath need to now be ready to be fitted in its final position.

 

 

Removing Old Taps

If you need to replace old faucets with brand-new ones as a part of your installment, after that the first thing you must do is separate the water supply. After doing so, turn on the faucets to drain any water continuing to be in the system. The procedure of removing the existing faucets can be rather problematic because of the restricted accessibility that is commonly the case.
Use a container wrench (crowsfoot spanner) or a tap tool to undo the nut that attaches the supply pipelines to the faucets. Have a towel all set for the continuing to be water that will certainly come from the pipes. When the supply pipes have actually been eliminated, utilize the same device to loosen up the nut that holds the taps onto the bath/basin. You will certainly require to quit the single taps from transforming throughout this process. Once the faucets have been eliminated, the holes in the bath/basin will have to be cleaned of any type of old sealing substance.
Before going on to fit the brand-new taps, compare the pipe links on the old faucets to the brand-new taps. If the old taps are longer than the new taps, after that a shank adapter is required for the new faucets to fit.

 

 

Mounting the Bathtub

Making use of both wood boards under its feet, position the tub in the needed placement. The wood boards are useful in evenly spreading out the weight of the bath tub over the location of the boards instead of concentrating all the weight onto 4 tiny factors.
The next objective is to ensure that the bathtub is leveled all round. This can be achieved by checking the spirit level and also readjusting the feet on the bath tub till the spirit level reads level.
To set up taps, fit the bottom of the furthest adaptable faucet adapter to the appropriate supply pipeline by making a compression sign up with; after that do the exact same for the various other faucet.
Activate the water supply as well as check all joints as well as brand-new pipework for leaks as well as tighten them if needed. Fill up the tub and additionally check the overflow outlet as well as the regular electrical outlet for leaks.
Lastly, deal with the bath paneling as described in the manufacturer's user's manual. Tiling and securing around the bathtub should wait till the bathtub has actually been made use of at least once as this will certainly resolve it into its last position.

 

 

Suitable New Touches

If the tails of the brand-new taps are plastic, then you will certainly require a plastic connector to avoid damages to the thread. One end of the adapter fits on the plastic tail of the faucet as well as the various other end gives a connection to the existent supply pipes.
If you need to fit a monobloc, after that you will certainly need decreasing couplers, which connects the 10mm pipe of the monobloc to the typical 15mm supply pipe.
Next off, position the tap in the installing opening in the bath/basin making certain that the washing machines are in area between the faucet and the sink. Protect the tap in position with the maker supplied backnut. As soon as the tap is safely in place, the supply pipelines can be linked to the tails of the faucets. The taps can either be linked by using corrugated copper piping or with normal faucet connectors. The former type must be connected to the tap ends first, tightening up just by hand. The supply pipes can later be connected to the other end. Tighten both ends with a spanner after both ends have been connected.

 

 

Tiling Around the Tub

In the location where the bath fulfills the tile, it is essential to secure the accompanies a silicone rubber caulking. This is important as the fitting can relocate sufficient to fracture an inflexible seal, creating the water to permeate the wall between the bathroom and also the tiling, bring about difficulties with moisture and feasible leakages to the ceiling below.
You can pick from a variety of coloured sealants to blend in your components and installations. They are offered in tubes as well as cartridges, as well as are capable of sealing spaces as much as a size of 3mm (1/8 inch). If you have a bigger gap to fill up, you can fill it with twists of drenched paper or soft rope. Keep in mind to always fill the bathtub with water before securing, to permit the motion experienced when the tub is in use. The sealer can break fairly early if you do not think about this movement before sealing.
Conversely, ceramic coving or quadrant tiles can be made use of to border the bathroom or shower tray. Plastic strips of coving, which are easy to use as well as reduce to dimension, are also easily readily available on the marketplace. It is recommended to fit the tiles making use of water-resistant or water resistant adhesive as well as grout.

 

A Step-by-Step Guide to Installing a Bathtub

 

Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.

But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.

This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.

 

Remove the Existing Bathtub

 

To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.

The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.

 

Choose the Right Bathtub

 

The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.

 

Install the Plumbing and Ledger Board

 

You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.

Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.

 

Install the Bathtub

 

When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.

Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.

If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.

 

Hook up the Plumbing

 

Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.

 

Install the Bathtub Surround

 

A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.

Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.

If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.

If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.

https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/

 

I ran across that write up about Installing A Bathtub while doing a search on the web. Feel free to set aside a second to promote this page if you enjoyed reading it. We treasure reading our article about A Step-by-Step Guide to Installing a Bathtub.

Plumbing integrity assured.